1. Opcom Key Fob Programming Keyless
2. Opcom Key Fob Programming Fob
3. Corsa C Key Fob Programming Opcom
4. Opcom Key Fob Programming Tutorial

It’s verified that only OPCOM OP-COM firmware version 1.39 running with VAUX-COM 2009 software can read security codes for key programming, all tested by users.

Program NEW, not previously programmed key(s) to the immobiliser system. Program Transponder Key - OLD program OLD, previously already programmed key(s) to the immobiliser system. new keys certification; make sure it works In short, setup in OPCOM: Year - vehicle - body - Cim - Programming - immo-programming - security-code - add. After each key, please cycle the ignition. If you want to program two, or three keys, please repeat the procedure. Program Transponder Key – OLD With this function, you can program OLD, previously already programmed key(s) to the immobiliser system. Only one keys can be programmed at once. After each key, please cycle the ignition.

Hunta says in http://www.corsa-c.co.uk/forum/

“opcom 1.39 has always worked for me reading security codes and for programming”

Marks152 says:

“1.39 is the ONLY firmware you should be running when using 100219a. It is designed to run with this software and is the ONLY version that will allow FULL use of the interface. Any firmware higher will restrict access to the instruments.”

Ssmith73 says:

“1.39 firmware can get a spare key fob programmed”

x-paul-x06 says in http://www.vauxhallownersnetwork.co.uk/

“opcom will read his security code but it should as i managed to down grade the firmware to 1.39”

Where to get old version OPCOM?

Opcom firmware v1.39 (not OPCOM V1.59)

VAUX-COM 100219a

Note: opcom fw: v1.39 with 2009 software is the only version to read security codes

Why you need security codes?

For programming new keys and immoboliser, functions the Security Code is required. This code can normally be found on the Pass. Unfortunately, the Car Pass is often lost.

What models can be read security codes?

With OP-COM you can read the security code from the following models:

Corsa-C  Meriva  Tigra-B

How to read security codes with OPCOM v1.39?

Choose Body

Choose Instrument

Choose EPROM info

Now the Security Code can be read from EPROM

How to use OPCOM 2009 software to program keys?

Opcom: Year -> vehicle -> body -> Cim -> Programming -> immo-programming -> security-code -> add new key

Immo

Security code

vProgram key

Before using OP COM China Clone to make key for your Astra, 4 things you need to know in advance.
1. NEW remote central locking board (PCB) to the car
2. A key to the car
3. The Security Pass for the car
4. Opcom OP-Com 2012V with Firmware V1.59
OPCOM
How to install Opcom firmware 1.59 (the following video link is offered for your reference)

Opcom Key Fob Programming Keyless

http://opcom-china-clone.blogspot.com/2015/09/op-com-opcom-2010v-firmware-159.html
And then the following part is the operation guide:
Step1. Insert your NEW remote central locking board into your key;
Step2. Put the key into the ignition and turn but Do Not crank the engine;
Step3. Connect OPCOM with your car and your computer (that has already finished software installation);
Step4. Open OPCOM software and click on “DIAGNOSTICS” (mark red at picture below);
OPCOM-1
Step5. A vehicle identification menu will pop out in the next page. Select your car year;
Step6. And then select your car model;
Step7. Select “BODY” from the menu.
OPCOM-2

Opcom Key Fob Programming Fob

Step8. Select “ANTI THEFT WARNING”;
Step9. Press “PROGRAMMING” button (locate on the right hand side of the screen);
Step10. Select “SECURITY CODE” (this should be the only one available at the time).
Step11. Enter your “SECURITY CODE” and click OK.
Step12. Select “PROGRAMMING REMOTE CAR KEY”;
Step13. Follow the on screen instructions.
Step14. Click “CLOSE”.
Step15. Open and close door, try locking your door and then dead lock it. Once you have done this, unlock and all should be done.

Corsa C Key Fob Programming Opcom

Opcom Key Fob Programming Tutorial